The SXFRH18 is the first Full frame CCD camera from Starlight Xpress with a mechanical shutter. It employs the Kodak KAF8300 chip with 8.3 megapixels in a 17.96 x 13.52mm format. The small 5.4 micron pixels of this camera allow maimum resolution with short focal length instruments.

The SXVR-H18 is another new development in the Starlight Xpress line of cooled CCD cameras. Until now, it was difficult for us to manufacture a camera based on a 'full frame' CCD, as such cameras need a mechanical shutter to avoid image smearing during download. We have now designed a shutter that is both reliable and small enough to fit inside the CCD chamber, allowing the introduction our first full-frame camera!

The SXVR camera line uses a two stage Peltier cooler for an extra 10 degree reduction in the CCD temperature to reduce the negative effects of the greater Kodak dark signal. A multicoated fused quartz optical window provides for reduced dewing and better UV/IR transmission. The fast 4.5 second download time minimizes the visibility of bias frame artifacts, such as hot columns and the top to bottom gradient that is commonly seen on such chips. We think that the result is a highly satisfactory monochromatic camera with excellent sensitivity and resolution.

SXVR-H18 Features:

• Large, high resolution Kodak CCD chip, with 8,300,000 x 5.4uM square pixels in a 17.96 x 13.52mm array
• High sensitivity, 56% QE at peak (540nM - green light)
• Very good H-alpha sensitivity (48% QE at 656nM)
• Low dark signal - Dark frames not necessary for most of the brighter deep sky objects
• Anti-blooming with minimal effect on linearity
• Fused quartz optical window for good thermal and optical performance
• Fast, low vibration electric shutter. Latency less than 0.05 seconds
• Fully user adjustable chip alignment for perfect focus across the entire field
• Built-in super high speed USB 2.0 interface for approx. 4.5 second downloads
• Built-in autoguider interface and output - compatible with the optional dedicated external guide camera
• Built-in dual serial ports for accessory control - directly drive filter wheels, GOTO 'scopes etc.
• Single USB cable control for all features - get rid of that dangerous cable tangle!
• Only ONE computer needed to control all of the devices and functions
• Very low power consumption. Less than 1.0 amps at 12v DC - 12VA at 110v or 240v AC
• Compact and lightweight - only 75mm in diameter x 70mm long - less than 500 grams load on the 'scope!

SXVR-H18 Specifications:

• CCD type: Kodak KAF8300M full frame CCD with low dark current and lateral anti-blooming.
• CCD Full resolution Pixel data: Pixel size: 5.4uM x 5.4uM, Image format: 3326 x 2504 pixels
• CCD Image area: 17.96mm (Horizontal) x 13.52mm (Vertical).
• CCD quality: Standard grade - No dead columns, no dead pixels.
• Spectral Response: QE max at 540nM (~56%), 48% at 470nM and 656nM.
• Readout Noise: Less than 10 electrons RMS - typically only 7 electrons.
• Full-well capacity: Greater than 25,000 e- (unbinned)
• Anti-blooming: Overload margin greater than 100x.
• Dark current: Dark frame saturation time greater than 10 hours. Less than 0.05 electrons/second @ + 10C ambient.
• Data format: 16 bits.
• System gain: 0.4 electrons per ADU
• Computer Interface: Built-in USB 2.0 compatible interface.
• Image download time: Typically 4.5 seconds at full resolution using USB 2.0
• Power requirements: 115VAC / 240VAC @ 12VA, or 12VDC @ 750mA max.
• Cooling system: Regulated constant current cooling supply with two stage thermoelectric cooler to give a CCD temperature of approximately -40C below ambient.
• Size: 75 x 70mm black anodised aluminium barrel with 42mm 'T2' thread at the CCD window end & input/output plugs at rear. CCD alignment screws are provided for setting the chip parallel to the focal plane.
• Weight: approx. 400g.

Back to List